Showing posts with label feeding cows. Show all posts
Showing posts with label feeding cows. Show all posts

Wednesday, September 24, 2008

The Wind Blew Right Through The Boards


I also spent many boring hours in the swamp in the late summer haying. Dad would have me mow the tules for cattle feed in the winter. It wasn't very good feed but there was lots of it. There was close to one hundred acres to hay. I would just go around and around the square field for several days to cut it all. The ranch was under the training flight path for jet fighters out of Nevada and Klamath Falls, OR. One day I was mowing hay in the swamp when one went over. The shadow and noise came at about the same instant, causing my heart to stop, and die, as the sound of the tractor covered up the jet noise until the moment of the shadow. Hauling those light tule bales was a breeze though compared to heavy alfalfa bales. We would stack the hay high up in the lower barn.


The lower barn was down close to the swamp at the north end of the property. No one that grandpa Leo ever talked to knew when it was built and it was always felt to be very old in the 1960's. All the main timbers were hand hewn and wooden pegs held them together. It was a very large hay barn, about one hundred twenty feet long, with manger stalls under the roof so the cattle could feed out of the weather. When it was empty and you looked inside knowing you were going to have to fill it you got a pretty overwhelmed feeling. Dad had put a tin roof on it. The roof came from buildings he helped tear down at the Pit 3 powerhouse.


I spent some the coldest times in my life in the lower barn feeding cows. The cold north winds would just pass right through the boards not to mention the sifting snows. Some mornings would be ten or more degrees below zero. I would get up in the barn and find several inches of frozen crusty snow on the bales. No amount of gloves or hard work could keep my skinny hands and feet warm. Sometimes it felt like I had no feet or hands left. When the tule hay ran out we would begin feeding off the back of the Hoopy. (See my blog of Sept. 8. 2008 for more about Hoopy)


In the mid 1980's we had to tear the lower barn down as it was starting to fall and had collapsed in one place. My father-in-law, Bob McKernan, along with help from Mexican hands, Bruce and me took the barn down. For some reason we all still loved that old barn no matter how daunting the job of filling or miserable the job of emptying it was.

Friday, September 5, 2008

Hauling hay on a wooden sled, exciting and dangerous

Hauling hay on a wooden sled, exciting and dangerous


Hauling hay on a wooden sled, exciting and dangerous. Grandpa Leo and dad built a sled from full 2x12 boards to haul hay bales from the field to a stack or barn. The sled must have been about eight feet wide and twice that long with a cable attached to the front of the sled and hooked to the tractor . We pulled it with our Model G, John Deere tractor, the B just wouldn‘t pull much hay.

I liked the G, it had an electric starter but could be cranked if the batteries were dead. The Model B had to be started by hand though. It had an exposed flywheel that you just grabbed hold of and gave it a spin (it almost always started). Usually I could start the B without opening the petcocks. The petcocks are valves on each cylinder (there is only two on these two models, Johnny Pops) that can be opened to relieve some of the compression. The G almost required the petcocks be opened to start even with the electric starter.

Back to hauling hay on a sled. You needed a tractor driver and a stacker. I was very happy when Bruce got big enough to be a stacker. The tractor driver would just drive beside the bales of hay and the stacker would grab the bales with hay hooks and stack them. Sounds easy and it was except when dad got the bales so heavy they out weighed me. Then the driver had to stop and the stacker would have to drag the bale up to the sled now because the driver went by it. The stacker would have to decide whether to buck the heavy thing up to an empty spot or start a new bottom layer. Start a new bottom layer sounds good but some times there are a bunch of heavy ones and you just can’t have that much bottom layer before going up with the stack.

Then when you get to the front of the sled the danger and excitement begins. It is probably being pulled between two and five miles per hour. If your little brother was mad at you he would just drive too fast to keep up with the bales. The driver has to watch where he is going or he runs over bales. The stacker must be careful to not step off the front of the sled so it doesn’t run over him and smear him under the sled until the driver noticed. The driver would never be able to stop in time.

Exciting!

Wednesday, September 3, 2008

I started driving Hoopy before I could reach the peddles.


Hoopy is a 1928 Chevrolet one ton truck my grandpa Leo bought new in Redding. When I was very young, I think before ten or so, dad would let me steer the Hoopy while he cut the bales and fed them from the back of the truck to the cattle. Most of the time this feeding was done near the lower barn. Dad would set the throttle and point me at a mountain in the Big Valley mountain range. He would then climb on the back and start feeding. Sometimes I would get too close to the swamp so dad would have to climb back inside, turn the wheel, and get me back on track.

I wasn't tall enough to reach the peddles so I could stop or strong enough to turn the wheel. Old vehicles had hand throttles so it could be set and just leave it. This is how I learned to drive.

As I got older, it was often my turn to feed from the back of the truck while Bruce (he's my little brother) or someone drove. Most of the time we drained the water from the radiator so it wouldn't freeze. It had too many leaks to put antifreeze in and waste it. One winter that was very cold I remember dad had to set a fire under the Hoopy's radiator to thaw the water. Hoopy wouldn't start after we poured the water in so the water froze. We only had to be careful of the lower hose because everything else was steel and it wouldn't melt.

Hoopy had to be hand cranked to start. Dad always told me to set the timing retarder/advancer before cranking it. He said it was more likley to kick back if not set right and the crank could break an arm. I think I always remembered to do that. It has wooden spokes for wheels, wooden slats in the roof, a four cylinder engine and four speed transmission.

I spent many an icy cold or wet rainy morning on the back of Hoopy too. Bruce still has Hoopy at his house in the hopes of getting it running again. I hope he does someday before it gets too deteriorated.